Hola, necesito comprar memoria RAM para placa GIGABYTE G41MT-D3. En la tienda no me la pueden conseguir y tengo que ir a segunda mano o cosas así. En la tienda han probado muchas y no iban, al final han encontrado 2 Gb, pero es poco. Me dicen que tienen que ser: 1333/1066/800 Mhz. Estoy buscando por internet y he encontrado esto:
2x4gb = 8gb Kingston ddr3 kvr1066d3n7/4g- PC3-8500 (DDR3 1066)
JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
VDDQ = 1.5V (1.425V ~ 1.575V)
533MHz fCK for 1066Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 6 (DDR3-1066)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration: Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
PCB: Height 1.18” (30mm), double sided component
SPECIFICATIONS
CL(IDD) 7 cycles
Row Cycle Time (tRCmin) 50.63ns (min.)
Refresh to Active/Refresh 160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 37.5ns (min.)
Power (Operating) 1.320 W*
UL Rating 94 V - 0
Y querría saber si son compatibles con mi placa. Os agradezco mucho de antemano la colaboración. Un saludo
2x4gb = 8gb Kingston ddr3 kvr1066d3n7/4g- PC3-8500 (DDR3 1066)
JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
VDDQ = 1.5V (1.425V ~ 1.575V)
533MHz fCK for 1066Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 6 (DDR3-1066)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration: Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
PCB: Height 1.18” (30mm), double sided component
SPECIFICATIONS
CL(IDD) 7 cycles
Row Cycle Time (tRCmin) 50.63ns (min.)
Refresh to Active/Refresh 160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 37.5ns (min.)
Power (Operating) 1.320 W*
UL Rating 94 V - 0
Y querría saber si son compatibles con mi placa. Os agradezco mucho de antemano la colaboración. Un saludo
